Without nserver (or fakeresolve) names were resolved by the C library.
3proxy's own resolver is now the default, with the system's name
servers: up to 3 from /etc/resolv.conf, on Windows from the registry
(set for the system, set for an interface with an address, Tcpip6
interfaces, then those DHCP gave). With none found, the C library as
before. nserver takes up to 3 as well (MAXNSERVERS), a fourth is
warned about.
The name servers in force belong to the process, not a configuration:
nserver lines are kept aside while a configuration is read and replace
them only once it is committed, so a reload resolves with those in
force until then. Resolutions and dnspr read a copy of them.
The system's are read at start, before the configuration and a chroot
in it, and are in force while it is read, so its host names resolve
with them; read again at a commit, and checked every 5 seconds from
the main loop while the default is in force. What cannot be read then
(within a chroot) stays as last read.
The hosts file, read with them, is imported into tables of its own
while the default is in force: its first address of a family for a
name. A name is looked up as one nsrecord made first, then the hosts
file, then the name cache, then name servers. A changed file replaces
what was imported. No name cache is made for it: without nscache
nothing is cached, as before.
The name cache's keys are host names of any case now: DNS names are.
Tests: sysdns, a name of the hosts file answered by dnspr without
nserver, in any case, and not with one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A reload reads the file into a new configuration, allocated from the
defaults, and prepares its services without starting them. Only if the
whole file is read without an error does it come into force: the old
configuration's services stop accepting, the new ones start. On an
error everything prepared is dropped and the old configuration, which
never stopped, stays in force.
Each service holds its configuration until it is freed, after its last
client; a configuration no longer in force is released when the last
holder lets go (confhold/confput). freeconf() now only releases what a
configuration holds, touching nothing global.
What runs without a service of its own reads the configuration in
force, runconf, rather than conf, which a reload points at the one
being read: the resolver, which holds it while it waits (a client
resolves with its own service's), the log, the thread pool, the admin
pages, which walk the services under config_mutex, and the signal
handlers.
The users table, havelog and the resolver choice are per configuration
now, the resolver applied when the configuration comes into force, so
a refused file leaves the users as they were. The log file, the
configuration file name, the string table, daemon mode and the filter
list belong to the process and are handed from one configuration to
the next. Settings left out of a new file go back to their defaults,
where before they kept the old values.
The gap between the old and the new listening sockets remains: a
connection queued on an old service's socket when it closes is reset.
Handing the socket over is the next phase.
A test case reloads a broken file (nothing changes, alice still gets
in, bob from the refused file does not) and a good one (bob only, the
service on its new port, the old one closed, a download through the
old service finishing whole). 40 reloads, a third refused, under load
show no memory errors under AddressSanitizer.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
conf is now a pointer to the current configuration rather than the
structure itself: at first confboot, which exists before main() runs, as
plugins and the standalone services use it too; later configurations
will start from confdefaults. Both are made from confinit.h, the one list
of initial values. The timeouts are an array of the configuration
instead of a pointer to a global one. Nothing behaves differently yet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They are the state of the process, not configuration: conf.time (now
curtime), timetoexit and needreload are globals of their own. Plugins
reach needreload through a pointer added at the end of struct
pluginlink; LdapPlugin uses it. The extern for a paused global, never
defined, goes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
nservers, numservers and authnserver (resolve.c, common.c) and
radiuslist, nradservers and radiussecret (authradius.c) were globals of
their own; they are configuration, set by nserver, authnserver and
radius, and now live in struct extparam with the rest of it.
MAXNSERVERS, MAXRADIUS and struct radserver move to structures.h, which
plugins include without proxy.h.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
