The command keeps the C library's resolution which a configuration
without nserver had before the system's name servers became the
default: no hosts file imported. nserver lines, if any, are still
there for dnspr to forward to. Of sysresolve and fakeresolve the last
given applies.
Tests: sysdns, with sysresolve dnspr has no hosts file names and a
name is resolved through the system routines.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Without nserver (or fakeresolve) names were resolved by the C library.
3proxy's own resolver is now the default, with the system's name
servers: up to 3 from /etc/resolv.conf, on Windows from the registry
(set for the system, set for an interface with an address, Tcpip6
interfaces, then those DHCP gave). With none found, the C library as
before. nserver takes up to 3 as well (MAXNSERVERS), a fourth is
warned about.
The name servers in force belong to the process, not a configuration:
nserver lines are kept aside while a configuration is read and replace
them only once it is committed, so a reload resolves with those in
force until then. Resolutions and dnspr read a copy of them.
The system's are read at start, before the configuration and a chroot
in it, and are in force while it is read, so its host names resolve
with them; read again at a commit, and checked every 5 seconds from
the main loop while the default is in force. What cannot be read then
(within a chroot) stays as last read.
The hosts file, read with them, is imported into tables of its own
while the default is in force: its first address of a family for a
name. A name is looked up as one nsrecord made first, then the hosts
file, then the name cache, then name servers. A changed file replaces
what was imported. No name cache is made for it: without nscache
nothing is cached, as before.
The name cache's keys are host names of any case now: DNS names are.
Tests: sysdns, a name of the hosts file answered by dnspr without
nserver, in any case, and not with one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
-s[N]:MIN,STREAK,SMALL sets where the automatic mode splices, as -g
does for grace delay: a direction is spliced after STREAK reads in a
row of MIN bytes or more (SMALL from a TLS socket), copied again after
more than STREAK splices in a row of less than SMALL, and a body of
known length is spliced if MIN or more of it is left. The defaults,
16384,2,4096, are what was built in; a value left out or 0 keeps its
default.
The man page describes it, and its HTML copy, which still said splice()
was not built by default, now has the current text. A test case relays
answers of every size, chunked ones and a 3 MB upload through every
mode, two of them with heuristics set, and compares them byte for byte.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ssl_ktls asks OpenSSL to hand TLS to the kernel (SSL_OP_ENABLE_KTLS)
on the connections of the services which follow, both to clients and
to servers; ssl_noktls, the default, keeps it in 3proxy. Where the
library, the kernel and the cipher allow it, the kernel then encrypts
and decrypts, and SSL_read/SSL_write go on working over it. What a
service got is logged on its first TLS connection.
Reading ahead is left off where the kernel took receiving, which reads
a record at a time. A build whose library has no kernel TLS (wolfSSL,
OpenSSL before 3.0 or without it) warns and ignores the command.
splice() is not used for TLS services yet.
Tested on AlmaLinux 10 (OpenSSL 3.5.8, tls module): both directions
of both legs of a TLS chain in the kernel, the suite passing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
nserver and authnserver parse their argument with parsehost(), which reads
the first colon as the address/port separator, so a bare IPv6 address picks
up a bogus port number. Document the bracket form in 3proxy.cfg(5) and in
both HOWTOs.
Refs #1275, #460
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
After 'parent ha' sends the PROXY v1 header, continue negotiating the
real parent protocol (SOCKS5/CONNECT/etc.) instead of returning early.
'ha' used alone still sends the header and relays plain TCP.
